Elcometer Moisture Meter Electrodes

ELECTRODES FOR MOISTURE MEASUREMENT IN BUILDING MATERIALS

Drive-in Electrode M 20

For measurement of timber up to 50mm thick. Electrode body of impact resistant plastic. Included in the delivery are ten spare pins 16mm and 23mm.

KT007400P003

Surface Measuring Caps M20-OF 15

For moisture measurements on surfaces without damaging the material. Effective up to depth of approximately 3mm. (Only to be used with electrode M20).

KT007400P042

Stick-in Electrode M6

For measurement on hard, solid building materials (mortar, concrete, etc). With two of each electrode pins 23mm, 40mm and 60mm long (only to be used with contact paste).

KT007400P007

Flat Electrode Pair M6-Bi 200/300

For moisture measurements on concrete or insulation materials in corner or expansion joints. (Only to be used with electrode insulated shank)

Pair of Brush Electrodes M25

Stainless steel electrodes, for measurements on hard and soft building materials without contact paste.

KT007400P089

Stick-in Electrode Pins M20-Bi 200/300

For measurement of materials hidden beneath another panel or covering. (Only to be used with electrode M 20)

Deep Electrodes M21-100/250

For deep measurements of all kinds of set building materials in conjunction with contact paste.

Stick-in Electrode Pins M 6-150/250

Extra thin probes for measuring the moisture content in building and insulating materials over expansion joints or through intersecting tile joints, non-insulated. For use with electrodes M6 and M20.

Active Electrode MB 35

With integrated measuring circuit, designed for surface measurement on concrete, in particular before coating, painting or colour marking. Measuring range: 2 to 8 % of dry weight

KT007400P032

Active Electrode B 50

With integrated measuring circuit, designed for non-destructive location of moisture concentration in building materials and moisture distribution in walls, ceilings and floors. The electrode uses a patented process to create a high frequency field with a penetration depth up to 120mm depending on the density of the tested building material.

Measuring range:

0 to 199 digits scanning range (classification according to table).
0.3 to 8.5 % of dry weight, conversion of reading by table,
0.3 to 6.5 % moisture content, conversion of reading by table.

KT007400P013

Active Electrode B 60

With integrated measuring circuit, designed for non-destructive location of moisture concentration in building materials and moisture distribution in walls, ceilings and floors. The electrode uses a patented process to create a high frequency field with a penetration depth up to 120mm depending on the density of the tested building material. With additional selector for setting a limit value between 20 and 140 digits and acoustic signal generator.

Measuring range:

0 to 199 digits scanning range (classification according to table).
0.3 to 8.5 % of dry weight, conversion of reading by table,
0.3 to 6.5 % moisture content, conversion of reading by table.

KT007400P082

ELECTRODES FOR WOOD MOISTURE MEASUREMENT

Drive-in Electrode M 20

For measurement of timber up to 50mm thick. Electrode body of impact resistant plastic. Included in the delivery are ten spare pins 16mm and 23mm.

KT007400P003

Ram-in Electrode M18

For moisture measurement in timber up to about 180mm thick. Supplied with ten spare pins 40mm and 60mm long.

Teflon insulated electrode needles for point measurements at different depths are also available.

KT007400P002

Active Electrode MH34

With integrated measuring circuit for measurement of high moisture contents in coniferous wood, specially in case of water-borne storage and for pre-sorting of freshly cut timber for kiln drying.

Measuring range: 40 to 200 % moisture content.

KT007400P033

Stick-In Electrode Pins M20-HW 200/300

For measurement of materials hidden beneath another panel or covering. (Only to be used with electrode M20)

ELECTRODES FOR TEMPERATURE MEASUREMENT

ET10

Robust stick-in temperature sensor for solid substances, bulk materials and fluids.

L ength of probe 100mm, diameter 3mm. Measuring range -50 to 250°C

KT007400P006

TT40

Robust immersion and combustion gas temperature sensor.

Length of probe 480mm, diameter 5mm, measuring range -50 to 350°C

KT007400P016

LT20

Fast reacting air/gas temperature sensor with probe.

Length 480mm, diameter 5mm. Measuring range -20 to 200°C

KT007400P018

TT30

Robust immersion and combustion gas temperature sensor.

Length of probe 230mm, diameter 3mm. Measuring range -50 to 350°C

KT007400P017

ET50

Fast reacting stick-in temperature sensor for soft solid substances, bulk materials and Fluids

Length of probe 120mm, diameter 3mm. Measuring range -50 to 300°C

KT007400P014

OTW90

Angled special surface temperature sensor for use at veneer presses etc.

Length of probe 100mm, diameter 5mm. Measuring range -50 to 250°C

KT007400P051

OT100

Spring loaded, low mass surface temperature sensor, for use on wall surfaces, etc.

Length of probe 110mm, diameter 5mm. Measuring range -50 to 250°C

KT007400P015

ELECTRODES FOR MEASUREMENT OF RELATIVE HUMIDITY

Special Electrode RF-T28

For high-speed testing of air relative humidity and air temperature, complete with connection cable.

Measuring range: 7 to 98% R.H. -10 to 80°C.

KT007400P013

Special Electrode RF-T36

For measurement of air humidity and air temperature, water activity value or equilibrium moisture in rooms, warehouses or solid substances (e.g. concrete, subflooring, masonry, etc.).

Measuring range: 5 to 98% R.H. -5 to 60°C.

KT007400P067

Plug-in Sensor RF-T31

For measurement of atmospheric moisture, water activity value or equilibrium moisture in bulk materials and solid substances, e.g. brickwork and other building materials.

Measuring range: 7 to 98% R.H. -10 to 80°C. Diameter 10mm, sintered filter tip 32mm long.

Blade Sensor RF-T32

For measurement of atmospheric humidity, water activity value and equilibrium moisture in paper, leather, textile and tobacco stores etc.

Range of Measurement 7 to 98% R.H. -10 to 80°C. Flat elliptical probe approx. 10 x 4mm