Subsite 250 Pipe and Cable Locator - Discontinued


PLEASE NOTE: THIS PRODUCT HAS BEEN DISCONTINUED – Please contact us if you would like a recommendation of a unit to replace this model.

subsite-250-pipe-cable-locator-receiver

Product Description

The Subsite 250 pipe and cable locator / Cable Avoidance Tool (CAT) offers a simple and safe solution to finding and tracing buried services up to a depth of 4.6 metresGet a grip on what’s beneath your feet with the 250R/T system, one of the most efficient and cost-effective methods for locating and avoiding buried telephone, CATV, power, gas, and water lines. Consisting of a 250T transmitter and a 250R receiver with passive or active capabilities, this simple, safe, light-weight system features intuitive controls, an easy-to-read display, and depth estimation up to 4.6 m. Whether you use it passively or actively, the 250R/T will help you get a handle on any situation.

The Subsite 250 R/T pipe and cable locator operates on the principle of detecting electromagnetic emissions from metallic services

  • Audible and visual display for use in noisy conditions with operator friendly controls and high visibility instruction labels.
  • Power mode is used to locate all live cables with sufficient current flow.
  • Radio mode is used to locate any metallic service carrying a (VLF) very low frequency signal.
  • Active mode is used in conjunction with the Transmitter to locate and trace a specific service which is an Optional Accessory

The Subsite 250 pipe and cable locator / Cable Avoidance Tool (CAT) was designed and built after consultation with engineers who used this type of equipment everyday.

Features

  • Simplified digital controls are arranged for easy operation.
  • Display is backlit & reinforced with a scratch-resistant coating for optimal visibility day, night, & well into the future.
  • Best-in-class dynamic range means the 250R/T can locate even when signals are extremely weak or strong.
  • Rugged design and moisture resistant cases stand up to long term use and tough weather conditions; housings are up to 2.5 times thicker in wearable areas than similar models.
  • Tones are derived from the actual signals radiating from pipes or cables, so even novice users can distinguish the signal from background noise.
  • Manufactured with 2/3 fewer components than similar models; fewer mechanical and electrical connections mean greater reliability.
  • With 1 Watt of power, the 250T is ten times more powerful than other transmitters in its class. It can apply 33-kHz signals via direct connect, induction clamp, or other optional accessories.

 

Specifications

Subsite 250 Pipe and Cable Locator – Specifications

Subsite 250 R Pipe and Cable Locator Receiver Specifications (250R) 
Dimensions  Receiver 
Length 290 mm
Height 70 mm
Width 100 mm
Weight 2.3 kg
Operation 
Operating Temp. Range -20 to 50°C
Antenna Configurations Twin Peak
Audio Output Speaker
Operating Modes : 
Active Line 33 KHz
Beacon (locate / depth only) 33 KHz
Passive Line 50 Hz or 60 Hz, no depth available
Radio Passive locate, no depth available
Locating Ranges : 
Line 4.6m
Beacon 3.0m
Maximum Depth Ranges (under ideal conditions. Actual operating field conditions with signal distortions or noise sources will affect tolerances)
Active Line ±5% 0.15 – 3.0 m
Active Line ±10% 3.0 m and deeper
Beacon ±5% 0.15 – 3.0 m
LCD Backlight Yes
Batteries 
Type 6 C-cell alkaline
Battery Life Approximately 40 hours (continuous use at 21° C)
Battery Saver Unit shuts off after 5 minutes of inactivity
Subsite 250 T Pipe and Cable Locator Transmitter Specifications (250T) 
Dimensions  Transmitter 
Length 311 mm
Height 235 mm
Width 114 mm
Weight 2.3 kg
Operation 
Operating Temperature Range : -20 to 50°C
Maximum Power Output 1 Watt
Operating Modes
Active Line 33 kHz
Batteries 
Type 6 C-cell alkaline
Battery Life Approximately 150 hours (continuous use low level power)

 

Data Sheet

Subsite 250 Pipe and Cable Locator – Data Sheet

Subsite 250 Pipe and Cable Locator Data Sheet

 

Instruction Manual

Subsite 250 Pipe and Cable Locator – Instruction Manual

Subsite 250 Pipe and Cable Locator Instruction Manual

 

Comparison Table

Pipe & Cable Locator Comparison

Pipe & Cable Locator Comparison
Subsite 150  Subsite 250  Subsite 950 
Receiver Y Y Y
Power Mode 1 Y Y Y
Live Cable Locator without Transmitter
Passive Power Frequency 50P,100Hz
Radio mode 2 Y Y
Detects Metallic Pipes without Transmitter (no Current) 3
Depth Range
Line +/-2m 4.2m 5m
Beacon +/-2m 3m 3m
Push button depth indication Y Y
Depth by Triangulation Y Y Y
Optional Accessories
Transmitter Y Y Y
Active mode 4 Y Y Y
Active Line Frequencies 5 30k Hz, 640 Hz 33 kHz 512 Hz, 1 kHz, 8 kHz, 29 kHz, 80 kHz, 33 kHz (EML)
Beacon / Sonde
Beacon mode 6 Y Y Y
Ranges of Beacons available 30kHz, 640Hz 33kHz 640, 512, 33kHz, 29kHz
Note :
1 Power mode is used to locate all live cables with sufficient current flow
2 Radio mode is used to locate any metallic service carrying a (VLF) very low frequency signal
The 250 has a specifically strong radio mode signal which makes it a very popular model
3 If the Metallic Pipe has a Current then the 150 can detect it in Power Passive mode
4 Active mode is used in conjunction with the Transmitter to locate and trace a specific service.
The Transmitter is an Optional Accessory
5 The 950 has a large range of Transmitter frequencies which is used when cables are congested and there is a chance of “bleeding” i.e. current jumping from one cable to another
6 Beacon Mode is used for Non Metallic pipes where you create a signal by inserting the beacon / sonde into the non-metallic pipe e.g asbestos, PVC or plastic The beacon is an optional accessory and needs to be purchased separately
Subsite 150 Pipe & Cable Locating System
Subsite 250 Pipe & Cable Locating System
Subsite 950 Pipe & Cable Locating System