Elcometer 207 and 207 DL Precision Ultrasonic Gauge - Discontinued

PLEASE NOTE: THESE PRODUCTS HAVE BEEN DISCONTINUED – Please contact us if you would like a recommendation of a unit to replace any of these models.

elcometer-207-and-207-dl-precision-ultrasonic-gauge-200

Product Description

The Elcometer 207 series of Precision Ultrasonic Thickness Gauge is designed to provide accurate measurements on thin materials.All Elcometer 207 and 207DL gauges also have the special PLAS mode. This is specifically designed to provide accurate readings when measuring thin plastics.

Using the latest transducer designs, the Elcometer 207 gauges can accurately measure material thickness from 0.15 – 25.4mm without the need to change the measurement mode.

Elcometer 207DL only – ElcoMaster™2.0

Measurement Modes

  • Interface-to-Echo Mode: The standard method for measuring material thicknesses from 1.65mm to 25.4mm.
  • Echo-to-Echo Mode: Measuring materials as thin as 0.15mm the Echo-to-Echo mode ignores the thickness of any coating applied to the surface under inspection.
  • PLAS Mode: A mode specifically used for measuring very thin plastics. A special graphite delay line accessory is required for this mode.
  • Differential Mode: Set an acceptable thickness (nominal) value in the gauge and the unit will display the positive or negative (±) difference from the nominal value entered.
  • Alarm Mode:Once a minimum acceptable thickness has been set, a red LED illuminates and a buzzer sounds if a measurement falls below the pre-set value.

Transducers

Elcometer Precision Ultrasonic Transducers are designed for thinner materials and have an accuracy to one  thousandth of one millimetre and are suitable for a range of materials: Cast Iron, Steels, Plastic, Glass and Aluminium.

The Ultrasonic transducer is available as a right-angled, microdot version only.

Part Number Measurement Range in Steel Frequency MHz Crystal Diameter Wearface Diameter
T92016526 0.15 – 25.4mm 15.0 green 6.35mm 7.42mm
Certificate available Certificate of Calibration: issued for Fixed Calibration equipment and shows readings and traceability
Accredited Certificate: can be issued for Fixed Calibration Equipment and a full UKAS traceable certificate is issued from an independent Calibration Laboratory

The Elcometer 207 and 207 DL Precision Ultrasonic Gauge can be used in accordance with:

  • ASTM E 797
  • EN 15317

 

Specifications

Elcometer 207 and 207 DL Precision Ultrasonic Gauge – Specifications

Part Number C207—-1 C207DL—-1
Interface-to-Echo Mode • •
Echo-to Echo Mode • •
PLAS Mode* • •
High Speed Scan Mode • •
Differential Mode • •
Alarm Mode • •
Data Output (immediate) • •
Data Logging (memory) 1000 readings
ElcoMaster™ Software •
Maximum Measurement Range 0.15 – 25.4mm
Velocity Range 1250 – 10000m/s
Accuracy ±0.02mm
Resolution 0.002mm
Units Millimetres and Inches
Operating Temperature -30°C to 50°C
Transducer Each unit is supplied with 15MHz, 6mm (¼”) microdot right angle transducer
Display 114mm (4½) Digit Liquid Crystal Display with backlight
Power AA 1.5V Alkaline or 1.2V NiCad cell
Battery Life 200 hours Alkaline (120 hours NiCad)
Weight 295g
Dimensions 63 x 120 x 31mm
Certificate available Certificate of Calibration: issued for Fixed Calibration equipment and shows readings and traceability
Accredited Certificate: can be issued for Fixed Calibration Equipment and a full UKAS traceable certificate is issued from an independent Calibration Laboratory

*   To use the PLAS mode, a special Graphite delay line is required which must be ordered separately – see Accessories

Part Number Measurement Range in Steel Frequency MHz Crystal Diameter Wearface Diameter
T92016526 0.15 – 25.4mm 15.0 green 6.35mm 7.42mm
Certificate available Certificate of Calibration: issued for Fixed Calibration equipment and shows readings and traceability
Accredited Certificate: can be issued for Fixed Calibration Equipment and a full UKAS traceable certificate is issued from an independent Calibration Laboratory


Elcometer 207 and 207 DL Precision Ultrasonic Gauge Packing List:

Elcometer 207 or 207DL gauge

  • ultrasonic couplant
  • 2 x batteries
  • carry case
  • microdot transducer
  • operating instructions

Data Sheet

Elcometer 207 and 207 DL Precision Ultrasonic Gauge – Data Sheet

Elcometer 207 and 207 DL Precision Ultrasonic Gauge Data Sheet

Standards

Elcometer 207 and 207 DL Precision Ultrasonic Gauge – Standards

The Elcometer 207 and 207 DL Precision Ultrasonic Gauge can be used in accordance with:

  • ASTM E 797
  • EN 15317

Accessories

Elcometer 207 and 207 DL Precision Ultrasonic Gauge – Accessories

Part Number Description
T92016871 Graphite Delay Line (for PLAS mode)
T92015701 Ultrasonic Couplant, 120ml Bottle
T92015874 High Temperature Ultrasonic Couplant, 60ml Bottle

Transducers / Probe for the Elcometer 207 / 207DL Ultrasonic Thickness Gauge

Elcometer Precision Ultrasonic Transducers are designed for thinner materials and have an accuracy to one  thousandth of one millimetre and are suitable for a range of materials: Cast Iron, Steels, Plastic, Glass and Aluminium.

The Ultrasonic transducer is available as a right-angled, microdot version only.

Part Number Measurement Range in Steel Frequency MHz Crystal Diameter Wearface Diameter
T92016526 0.15 – 25.4mm 15.0 green 6.35mm 7.42mm
Certificate available Certificate of Calibration: issued for Fixed Calibration equipment and shows readings and traceability
Accredited Certificate: can be issued for Fixed Calibration Equipment and a full UKAS traceable certificate is issued from an independent Calibration Laboratory

Sound Velocities

Sound Velocities / Speed of Sound in Materials for Ultrasonic Thickness Gauges

The Ultrasonic Thickness Gauges can be programmed by the user to the appropriate Material in two ways :

  • Using known standards of the same material – set the calibration to the thickness
  • Using the Frequency calibration, set the frequency to the appropriate Material using the Velocity / Speed of Sound Chart below.
Metals
m/s m/s
A Aluminium 6 320 – 6 400 M Molybdenum 6 250 – 6 300
Aluminium (2024-T4) 6 380 Mercury 1 450
Asbestos Cement 2 200 N Nickel 5 480 – 6 040
B Beryllium 12 880 P Platinum 3 690
Boron Carbide 10 920 S Silver 3 600 – 3 700
Brass 4 390 Steel, Mild 5 900 – 6 100
C Cast Iron 3 500 – 5 600 Steel, Casting (4340) 5 850
Cast Iron (Modular  Graphite) 5 600 Steel, 303 Stainless (Austenitic) 5 660 – 6 120
Cast Grey Middle 4 600 Stellite 7 050
Copper 4 650 – 4 720 T Tin 3 300 – 3 330
Cadmium 2 770 – 2 800 Titanium 5 900 – 6 100
Chromium 6 200 Tungsten Carbon 6 650
G Gold 3 200 – 3 250 Tungsten 5 180 – 5 400
I Inconel 5 820 U Uranium 3380
Iron 5 890 – 5 930 W Wolfram 5 460
L Lead 1 960 – 2 400 Z Zinc 4 170 – 4 320
M Manganese 4 660 – 4 700 Zircaloy 2 4 700
Magnesium 5 770 – 5 840 Zirconium 4 650
Non-Metal
m/s m/s
A Acrylic 2 870 N Nylon 2 600 – 2 690
Acrylic Resin 2 730 – 2 870 O Oil (SAE 30) 1 740
Air 330 P Paraffin Wax 2 200
Aluminium Oxide 8 700 Perspex 2 860
C Ceramic (Macor) 5 631 Phenolic 1 400
Diamond 17 500 Plexi Glass 2 690
Diesel Oil 1 250 Polyamide 2 380
Epoxy Resin 2 650 Polyethylene 1 900 – 2 400
G Glass (Flint) 4 260 Polyurethane 1 780 – 1 900
Glass (Crown) 5 260 – 6 120 Polystyrene 2 340 – 2 400
Glass (Quartz) 5 570 Porcelain 5 600 – 5 900
Glass (Window) 6 800 PVC 2 400
Glycerine 1 930 Q Quartz X Cut 5 740
I Ice 3 980 Quartz Fused 5 980
H Hi-Density Polyethelene 2 220 – 2 300 Rubber (Butyl) 1 900
        (Grey & White, Not Black) R Rubber (Soft) 1 480
M Methylene-Oxide 9 980 Rubber (Vulc.) 2 300
Monel 5 360 – 5 400 S Silicone Rubber 948
Motor Oil (SAE 30) 1 750 T Teflon 1 350 – 1 520
N Neoprene 1 600 W Water 1470
NB Note : This Schedule is only a Guide

Instruction Manual

Elcometer 207 and 207 DL Precision Ultrasonic Gauge – Instruction Manual

Elcometer 207 and 207 DL Precision Ultrasonic Gauge Instruction Manual